electric bike RSS

Order random 5 motors from below 10 types motors, can get a free Esk8 remote (US$65.9/pcs value) All are maytech popular motors:  1. MTO6355-200-HA 200KV Unsealed Sensored 8mm Shaft 2. MTO6355-170-HA-C 170KV Sealed Sensored 8mm Shaft 3. MTO6365-200-HA 200KV Unsealed Sensored 8mm Shaft 4. MTO6365-170-HA-C 170KV Sealed Sensored 8mm Shaft 5. MTO6365-170-HA-C2 170KV Sealed Sensored 10mm Shaft 6. MTO6374-190-HA 190KV Unsealed Sensored 8mm Shaft 7. MTO6374-170-HA-C 170KV Sealed Sensored 8mm Shaft 8. MTO6374-170-HA-C2 170KV Sealed Sensored 10mm Shaft 9. MTO6396-170-HA-C3 170KV Sealed Sensored 10mm Shaft with Big Ball Bearing 10. MTO6880-190-HA-C3 190KV Sealed Sensored 10mm Shaft with Big Ball      Bearing Where to order? Check Below...

Read more

1. If a vehicle does not need mechanical brakes, but must be able to brake, it must use electronic brakes. The principle is that the kinetic energy on the motor and the load can be used as a generator through the DC motor to convert the kinetic energy into electrical energy. Then the electric energy is consumed by heating and charging.   2. The electric energy that is emitted must not only charge the battery, but also release the heat. What is the process? 2.1 At this time, VESC has to make a distribution, which current is used to charge...

Read more

How to Install Motor on MTSKT310DB Dual Belt-driven Truck? Check below Video: New Gravity Casting Technology: 1. Aluminum liquid flow into truck mould by liquid's weight naturally, this way can delete mould's inside air clearly.2. do heat treatment after demoulding (truck surface is a little rough because of heat treatment). Prouction time is longer than old die casting technology, and the production cost is twice than before.3. Hardness reached out HRB65 around, which can stand over 150kg weight for professional skateboarders.     Compatible Motor: 5055/5065/6355/6365/6374 Motor Mount: 30mm and 44mm hole distance  1. Maytech Brushless Outrunner Sensored Motors 2....

Read more

1. Remote Apperance: 2. Receiver wiring instruction with VESC or VESC based Controllers:  There's 2 ways to connect receiver and VESC: 1. Connect VESC signal cable to receiver PWM; 5V; GND (as above receiver pin definition) 2. You can also use UART:  Cross connection of Receiver TXD/RXD and VESC RX/TX: Receiver’s TXD>> VESC RX;Receiver RXD>> VESC TX, 5V and GND also need to be connected, better use stranded wire, wire length should be shorter than 20cm. VESC supports UARR and PWM(PPM) throttle control. When use with Maytech waterproof remote, you can select PPM and UART, and select corresponding control in remote...

Read more

Some customers may ask: I still can't successful connect VESC to VESC_TOOL after VESC driver is installed, what should I do? After VESC driver is installed, doesn't mean the VESC is successfully installed, you need to choose correct virual serial port number in VESC_TOOL, if the virtual port number choose incorrect, still can't correct, check below steps: 1. When you first connect VESC to VESC_TOOL or when firmware is updated, driver will be installed automatically, please make sure your computer has network. (If the driver does not installed automatically, check former article,3 Ways to Install VESC Driver?) 2. After driver...

Read more