Maytech MTSVESC6.0M Mini VESC 35g 10S 42V VESC6.0 based Controller 30A for Combat Robots/Delivery Robots

Maytech.cn--Maytech official website

$159.90 Precio habitual $233.75
SKU: MTSVESC6.0M

Maytech MTSVESC6.0M Mini VESC 35g 10S 42V VESC6.0 based Controller 30A for Combat Robots/Delivery Robots Arm Robotics/Camera Motorized Dolly / Smart Robot Lawnmower

 


 

Model No. MTSVESC6.0M Cont. Current 30A
Burst Current 50A Input Voltage 42V(10S)
Hardware Based on VESC6.0 Firmware  Updatable 
Software VESC_TOOL Compatible FOC  Yes, can work 
Size 
65mm*20mm  Compatible Motor Sensored / Sensorless Motor
Net Weight 35g/pcs

 

This VESC is mainly used for robots products, do not suggest to use on electric skateboard, please noted. 

This VESC is new product, now we don't have stock. 

After your order confirmed, shipping time is about 1 month. 

If you still have any question, please contact us at agnes@maytech.cn 



Electric speed controller 72V for fighting robots robotics combat robots fire fighting robots, DIY fire fighting robot, DIY fighting robots,  fighting robot, fighting robots, robot, robots, sumo fighting robots, Minibot battle,  Robot fight, robot fighting,  robot wars, war robots, BattleBots, 10S 42V electric speed controller VESC6.0 based speed controller for electric skateboard elongboard mountainboardBattle robots, robot battle, Robot combat, Giant Fighting Robots, Giant robot fight,

robot arm Articulated Robots robot dog camera motorized dolly lawnmower lawnmower robot fighting robots, robotics

Attention Points when you receive the VESC Please:

All products had been double checked and tested one by one before shipment, only if the products are working normally would be shipped out. 

  • When you receive the VESC, please test without load and do not connect motor, first check if the VESC can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
  • Do not use switching power supply, the instant voltage when switching power supply connect to VESC is very high, which would easy damage the VESC.
  • Do not push the throttle too hard when test without load, gently and slowly speed up.
  • Be cautious when adjust parameters, if parameters set mistake, would also easy damage the VESC.
  • Please must remember to change to corresponding modes when you adjust parameters, for example, the VESC default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESC_TOOL didn't change to FOC mode, then when you push throttle, would easy burn the VESC, same as FOC mode.
  • In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage 
    ERPM= motor pole pairs number * KV * Voltage
  • If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
  • For V4 based VESC:

          Do not suggest to use FOC mode, suggest to use BLDC mode. 
          If need to use FOC mode, then must use voltage under 20V.

  • The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted


    Related Products: (Click the following pictures to check more products)

    Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes 

    Pre-sale Maytech New Remote for Electric Skateboard MTSKR2005WF V2 Waterproof Hand Remote

    Maytech Brushless Outrunner Sensored Motors

    Maytech brushless outrunner motor for electric skateboard 6355/6374/6365.6880/6396 sensored brushless engines

    Maytech VESC_TOOL Compitable VESC:

    Maytech Benjamin Vedder bruhsless VESC electric speed controller SUPER ESC dual vesc