Skip to content
Maytech.cn--Maytech official website Maytech.cn--Maytech official website
Account
Search
Loading...
Cart
  • All Brushless Motors
    • Brushless Outrunner Sensored Motor
    • Brushless Outrunner Sensorless Motor
    • Brushless Inrunner Sensored & Sensorless Motor
    • Brushless Hub Motor
  • All Speed Controller
    • VESC Controller for Esk8/Robot/E-bike
    • BLheli Firmware 32bit ESC for Drone
    • Falcon-Pro 32bit Firmware & Harrier-Eco ESC for Airplane/Helicopter
  • Esk8/Esurf/Robotics, etc.,
    • Remote Controllers
    • Speed controllers for Esk8,Mountainboard, robots
    • Motors for Esk8,Mountainboard, robots
    • Kits for Esk8/mountainboard/Robot
    • Truck, Belt, Pulley, wheel, etc., for Esk8, Mountainboard, Robots
    • Speed Controllers for Esurf/Efoil/Boat
    • Motors & Props for Esurf/Efoil/Boat
    • Kits for Esurf/Efoil/Boat parts
  • Airplane/Drone Parts
    • All Airplane/Helicopter Motors
    • All Airplane/Helicopter ESCs
    • All Airplane/Helicopter Propellers
    • All Drone/Multicopter Motors
    • All Drone/Multi-copter ESCs
    • All Drone/Multi-copter Propellers
  • About Us
  • OEM Project
  • Account
  • Home
  • / News and Guidence.
  • / How to Install Cooling Fan and UBEC to MTVESC6.12 ?

How to Install Cooling Fan and UBEC to MTVESC6.12 ?

How to Install Cooling Fan and UBEC to MTVESC6.12 ?

Posted by maytech@maytech.cn maytech@maytech.cn on 4월 30, 2020

MTVESC6.12 cooling fan installation instructions

  1. Fan specifications:

Model no: AVC DV05028B12U

Size: 50×50×28mm

Bearing type:Double ball bearing

Life span: 100 000H(Under the circumstances of 25℃,45~85% relative humidity)

RPM: 15000

Rated voltage / current: 12V/1.65A

Advantages: Maintenance-free double ball bearings, long service life, with sufficient cooling air volume and pressure.

cooling fan for Maytech New 200A MTVESC6.12 SUPERCASE200A VESC6 based controller for Robotics Efoil Electric Surfboard e-Skateboard

  1. Accessories quantity:

BLDC Fan 1 pcs  

M3*8 Hexagon socket head cap screws 4 pcs

DC-DC(UBEC) module 1 pcs: input 18-75V, output 12V 2500mA.

22AWG silicone wires 200mm length 2pcs

22AWG silicone wires 100mm length 2pcs

cooling fan and dc-dc module for Maytech New 200A MTVESC6.12 SUPERCASE200A VESC6 based controller for Robotics Efoil Electric Surfboard e-Skateboard

  1. Installation process:

3.1 Weld 100mm black and red silicone wires to Fan’s balck and red wires. And please wrap the welding part with heat-shrink tubes.

3.2 Unscrew the MTVESC6.12 case M3 screws (4pcs) and gently remove MTVESC6.12 case.

 Maytech New 200A MTVESC6.12 SUPERCASE200A VESC6 based controller for Robotics Efoil Electric Surfboard e-Skateboard

3.3 Weld 200mm black and red silicone wires to ESC capacitor PCB as following picture. Pay attention to the position of the red and black wires.

3.4 Lead the 200mm red and black silicone wires through the black rubber ring. Close the case and install the screws.

cooling fan for Maytech New 200A MTVESC6.12 SUPERCASE200A VESC6 based controller for Robotics Efoil Electric Surfboard e-Skateboard

3.5 Connect the 200mm and 100mm wires to DC-DC module:
200mm Red wire to VIN, 200mm Black wire to GND;
100mm Red wire to +Vo, 100mm Black wire to 0V.

Maytech New 200A MTVESC6.12 SUPERCASE200A VESC6 based controller with cooling fan

3.6 After checking all in good and correct connection, connect the ESC to a power supply above 18V. After one second of power-on, the fan starts to run. Be careful not to touch the fan blades.

  1. Fan switch:

The fan switch is not provided in the kit. Once the power is turned on, the fan will rotate normally. If you want to add a fan switch, there are two options:

4.1 Connect a switch in series between the 12V output port + Vo of the DC-DC module and the fan power cable. Note that you must choose a switch that can withstand more than 2A.

4.2 Connect a switch in series between the CTRL port and GND of the DC-DC module. When CTRL and GND are connected, the module turns off the output, and when CTRL and GND is disconnected, the module turns on the output. Recommend this option.

DC-DC module UBEC 18-75V to 12V

  1. other instructions:

5.1 The DC-DC module does not work when the input voltage is lower than 18V. If you need a DC-DC module that can also work below 18V, please contact us.

5.2 In this solution, the fan speed is constant. If you want to adjust the fan speed, a DC voltage regulator is needed to adjust the fan voltage between 5-12V. You can even DIY a temperature-controlled speed control board to automatically adjust the speed according to the temperature of the housing.

5.3 The fan usually does not need to be lubricated during its life. If you want to add lubricating oil, you need to disassemble it: remove the fan label, remove the nylon retaining ring and the blade and then add oil on the bearing.

Share this: Share on Facebook Tweet on Twitter Pin on Pinterest

Previous

More reference: FAQ 2 (frequently asked questions) about VESC controller
4월 24, 2020

More reference: FAQ 2 (frequently asked questions) about VESC controller

Next

What is BEC and UBEC? What is the difference? Why do I need an UBEC?
5월 09, 2020

What is BEC and UBEC? What is the difference? Why do I need an UBEC?

Collections

Remote Controller

Kits and parts for Efoil/Esurf/RC Boat

VESC_TOOL Compatible Controllers

Brushless Outrunner Sensored Motor

Maytech MTSKR1905WF V2 IP67 Waterproof Remote Control 2.4GHz wireless hand remote compatible with VESC for Esk8 Esurf Efoil Hydrofoil RC Boat

Maytech MTSKR1905WF V2 IP67 Waterproof Remote Control 2.4GHz wireless hand remote compatible with VESC for Esk8 Esurf Efoil Hydrofoil RC Boat

$6.00 Regular price $7.50

This is the perfect product!

We couldn't have asked for a better service!

Location

About Maytech

We are company integrated with design, development,

manufacture and sale for over 13 years, we do brushless motor, controller, remote , etc electronics for electric skateboard, electric surfboard, flight model products. 

Featured articles

Maytech MTSKR2005WF New Remote Instruction
8월 07, 2020

Maytech MTSKR2005WF New Rem...

1. Remote Apperance: 2. Receiver wiring instruction with VESC or VESC based Controllers:  There's 2 ways to connect receiver and VESC:...

Read more
  • All Brushless Motors
    • Outrunner Sensored Motor
    • Outrunner Sensorless Motor
    • Inrunner Sensored & Sensorless Motor
    • Hub Motor
  • All Speed Controller
    • VESC Controller for Esk8/Robot/E-bike
    • Waterproof & Watercooled ESC for Esurf
    • BLheli Firmware 32bit ESC for Drone
    • Falcon-Pro 32bit Firmware & Harrier-Eco ESC for Airplane/Helicopter
  • Esk8/Mountainboard/Robotic Parts
    • Remote Controllers
    • Electric Skateboard Parts
    • Esurf/Efoil/Boat Parts
    • Esk8/Robots Comb
  • Efoil/Esurf/Hydrofoil Parts
    • Waterproof & Watercooled Inrunner Motor
    • Waterproof Remote
    • Esurf ESC Powerful
  • About Us
  • OEM Project
  • Shipping & Warranty
Copyright © 2021 Maytech.cn--Maytech official website. Theme by Clean Canvas. Powered by Shopify
  • All Brushless Motors
  • All Speed Controller
  • Esk8/Mountainboard/Robotic Parts
  • Efoil/Esurf/Hydrofoil Parts
  • About Us
  • OEM Project
  • Shipping & Warranty
PayPal