1
/
von
9
Maytech.cn
In Stock Alloy Alluminum Heat Sink for MTSPF50A VESCTOOL Compatible Controller
In Stock Alloy Alluminum Heat Sink for MTSPF50A VESCTOOL Compatible Controller
Normaler Preis
$33.21 USD
Normaler Preis
$36.90 USD
Verkaufspreis
$33.21 USD
Stückpreis
/
pro
Versand wird beim Checkout berechnet
Verfügbarkeit für Abholungen konnte nicht geladen werden
Maytech Heat Sink Aluminium Case for MTVESC50A Electric Speed Controller Heat Dissipation Case
Weight:175g
Texture: Aluminum
Colour: Metal
Application: Heat Dissipation
Compatible to: Maytech MTSPF50A V4 based Controller
CNC machined Aluminium case for Maytech Superesc MTSPF50A BLDC VESC V4.12
Case protects the board from dirt, dust and overheating.
Recommended Products: (Click the following pictures to check specs)
1. MTVESC50A V4 based Speed Controller:
Share
Frequently Bought Together
In Stock Buy One Get One ! SuperESC MTSPF50A V4 based 50A Speed Controller 12S Lipo 50V$109.90- +
In Stock Brushless 6374 Unsealed Motor 8mm Shaft Sensored 90/190KV$148.50$133.65- +
In Stock Maytech Electric Skateboard Splashproof Remote Control MTSKR2005WF IP66 2.4GHZ$76.90- +
In Stock V5 Bluetooth Module Can Automatically Switch VESC Communication with Receiver or Bluetooth Module$47.80$43.02- +
In Stock Maytech Foil Boost VESC 100A V6 Speed Controller with Heat Fin for SUP Foil Esk8 Robots$141.70$127.53- +
In Stock SUPERFOC6.8 50V V6.0 based Speed Controller Great FOC Function$159.00$143.10
×
In Stock Buy One Get One ! SuperESC MTSPF50A V4 based 50A Speed Controller 12S Lipo 50V
Limited Offer: Buy MTSPF50A get Free Heat Dissipation Case
Freebie Quantity is Limited, First Come First Get !!!
*If you also need case, please order controller and case together according to below steps, if only order VESC, case will not be shipped together.
Discount Code: FREE50ACASE
| Model No. | MTSPF50A |
| Input Voltage | 3-12S Lipo (12.6V-50V) |
| Hardware | VESC4.0 |
| Firmware | Updatable |
| Cont Current | 50A |
| Burst Current | 240A |
| Software | VESCTOOL Compatible |
| Heat Sink | Order together if you need, optional |
| Application | Electric skateboard, elongboard, fighting robots, ebike, escooter, electric vehicles, friction drive ebike, etc., |
Attention Points when you receive the SuperESC Please:
All products had been double checked and tested one by one before shipment, only if the products are working normally would be shipped out.
- When you receive the SuperESC, please test without load and do not connect motor, first check if the SuperESC can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
- Do not use switching power supply, the instant voltage when switching power supply connect to SuperESC is very high, which would easy damage the SuperESC.
- Do not push the throttle too hard when test without load, gently and slowly speed up.
- Be cautious when adjust parameters, if parameters set mistake, would also easy damage the SuperESC.
- Please must remember to change to corresponding modes when you adjust parameters, for example, the SuperESC default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESC_TOOL didn't change to FOC mode, then when you push throttle, would easy burn the SuperESC, same as FOC mode.
-
In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage
ERPM= motor pole pairs number * KV * Voltage - If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
- For V4 based SuperESC:
Do not suggest to use FOC mode, suggest to use BLDC mode.
If need to use FOC mode, then must use voltage under 20V.
If need to use FOC mode, then must use voltage under 20V.
-
The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted
V5 Bluetooth Module:
| Model No. | MTBLEV5 V5 Upgraded version |
| Features | With optocoupler isolation, industrial grade anti-interference, and wired long distance communication |
| Upgrade Function | It supports connection together with receiver TXD and RXD to VESC, so it can automatically switch VESC communication with receiver or bluetooth and you don't need to unplug connections. When bluetooth module connect to VESCTOOL App, it will automatically disconnect receiver TXD and TXD, really convenient. |
| With 6 LED Lights status | power, communication, data tranmission |
| Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
| Compatible Software | VESCTOOL App |
| Frequency | 2.4Ghz |
| Distance | 15m |
| Input Voltage | 3.3-24V |
| PCB Size | 46mm x 32mm |
V2 Bluetooth Module:
| Model No. | MTBLEV2 V2 Version |
| With 3 LED Lights status | power, communication, database |
| Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
|
Compatible Software |
VESCTOOL App |
| Frequency | 2.4Ghz |
| ARM Processor | ARM Cortex-M0 32 bit processor 256kB flash&16kB RAM |
| PCB Size | 41mm x 21mm |
| Net Weight | 5g |
| Antenna Length | 90mm |
Recommend Products: Click below pictures to check more information
Brushless Outrunner Motors: 
×
2. Shipping time is about 24 working hours after your order confirmed if the product you ordered is in stock, if not in stock, lead time is about 30-40 days.
3. Motor wire leads out position is specific, if wind one more circle or one less circle, the KV would differ much, hard to make exact KV, so each motor might has ±5%-10% tolerance, this is normal.
$148.50$117.72
In Stock Brushless 6374 Unsealed Motor 8mm Shaft Sensored 90/190KV
Maytech Brushless 6374 190KV Open Cover Outrunner Sensored Motor for Esk8/E-bike/Fighting Robots/Mountainboard/E-scooter
|
Model No
|
MTO6374-HA |
KV
|
90/170/190 |
|
Idle Current
|
0.8A
|
Max Current
|
65A
|
|
Inpur Voltage
|
2-12s Lipo
|
Max Output Watt
|
3550W
|
|
Max Pull
|
13000g
|
Rated Current
|
60A
|
|
Motor Weight
|
825g
|
Shaft
|
8mm
|
|
Output Shaft Length
|
26mm
|
Internal Resistance
|
0.0402
|
Notice:
The motor has upgraded hall sensor embedded into stator, hall sensor board is more stable and motor has more precise positioning and smoother startup.
Printing on the motor case also has updated to with CE & ROHS symbol.
The upgraded version can work with previous version in same KV.
New embeded hall sensor version VS old version:
1. New version is with embedded hall sensor to stator:
Hall sensor board is more stable and motor has more precise positioning and more smooth starup.
2. With changing the hall sensor position, inside space is bigger than before and the original small bearing inside the stator can be replaced with a larger model, which increases the lifetime of the motor.
3. Mounting holes are updated to 8x M4 with deeper thread 11mm. Motor installation will be firmer.
Stock Notice Before Place Order:
1. The motor 90KV and 190KV are stock item, but stock is limited, so please confirm your order asap, or please contact us agnes@maytech.cn to check stock first if you need very urgently.170KV is not stock item, if you need this KV or other KV production takes about 35-55 days.
2. Shipping time is about 24 working hours after your order confirmed if the product you ordered is in stock, if not in stock, lead time is about 30-40 days.
3. Motor wire leads out position is specific, if wind one more circle or one less circle, the KV would differ much, hard to make exact KV, so each motor might has ±5%-10% tolerance, this is normal.
Motor Drawing:
Related Products: (Click the following pictures to check more products)
Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes
Maytech Brushless Outrunner Sensored Motors
Maytech VESC_TOOL Compitable controller:
Maytech MTSKR1712 Small and Light Cheap Remote:
×
Maytech MTSKR2005WF IP66 Splashproof Esk8 Remote Electric Skateboard Elongboard Hand Remote with 3 Speed Modes
2. Display voltage in V, current, temperature when work with VESC based controller
In Stock Maytech Electric Skateboard Splashproof Remote Control MTSKR2005WF IP66 2.4GHZ
Maytech MTSKR2005WF IP66 Splashproof Esk8 Remote Electric Skateboard Elongboard Hand Remote with 3 Speed Modes
Notice:
This remote is splashproof, can only use for electric skateboard, mountainboard, elongboard, please do not use for any water sports, otherwise all consequences are at your own risk.
If you want to use for water sports, then please order our MTSKR1905WF IP67 waterproof remote Here>
Specifications:
| Model No. | MTSKR2005WF (MTSKR20WFV2) |
| Waterproof Rank | IP66 splashproof |
| Speed Display | Yes |
| Throttle and brake Display | ±100% |
| Speed Mode |
3 speed modes, each mode can adjust speed from 1%-100% throttle |
| Charger |
QC 2.0 wireless |
| Display Screen |
OLED yellow & blue screen |
| Throttle and Brake Signal Output Range |
1.5ms-2ms for throttle; 1.5ms-1ms for brake |
| Voltage Display |
Remote & main battery voltage level (lithium iron; lithium ion battery optional) |
| Telemeter Data by Receiver |
Motor RPM; main battery voltage |
| Telemeter Data by VESC | ESC voltage/ current/ temp; Motor temp/ RPM |
| Triggers | 2x high senstive triggers |
| Wireless Frequency | 2.4GHz wireless with 40 channels |
| VESC Control Mode | Duty Cycle/ Current Mode |
| Travel Mileage | Yes |
| Receiver Built-in Switch for Esk8 Light / Esurf Water Pump |
1x 30V 3A mechanical relay switch; 1x 20V 2A transistor electronic switch |
| Accessories | Wireless charging pad; receiver; 3pcs dupont cable |
| Compatible ESCs | VESCTOOL/ Focbox/ Other PWM ESCs that has same signal output range with the remote |
| Application | Only for Electric skateboard, elongboard, mountainboard |
Features:
1. Display speed (km/h or mph) in Esk8 mode (for electric skateboard)2. Display voltage in V, current, temperature when work with VESC based controller
3. Display RPM (by 3 ways, hall sensor, VESC, motor wire)
> Get Manual: Remote Manual and Instruction
If your surrounded has strong magnetic interference, the signal might easy get lost, suggest you order the version with 1m or 3m Extend Antenna Here >
Tips for Usage:
1. This remote only has Esk8 mode, and it's just normal waterproof, can only work for electric skateboard, please do not use for Esurf.
2. The receiver is not waterproof, please keep the receiver away from water, otherwise the receiver would easy to have short circuit problem.
3. Please attention when weld wire on the receiver or when using, each 2 pins do not touch each other, otherwise would easy to burn the receiver.
2. The receiver is not waterproof, please keep the receiver away from water, otherwise the receiver would easy to have short circuit problem.
3. Please attention when weld wire on the receiver or when using, each 2 pins do not touch each other, otherwise would easy to burn the receiver.
Go to the following Youtube Links to check the remote instruction videos:
1. 3 Speed Mode Setting: https://youtu.be/bSyG4k-D76U
2. Remote Main Battery Display Setting: https://youtu.be/ibd0431_NSg
3. Sub-menu 7-14 Settings: https://youtu.be/O8IgYdbT2-A
Wiring Diagram with VESC:
t the ports according to the functions you need, no need to connect all ports.
1. PWM_T, +5V, GND (Receiver) - PWM, +5V, GND (VESC): Remote and VESC communication;
2. BAT(Receiver) - Positive Pole (Main Battery): Display main battery bar;
3. Receiver TX & RX cross connect with VESC RX & TX: UART, can display speed and distance, also voltage, current, temperature values
4. Relay Switch: To control Pump
5. Transistor Switch: To control light
6. Any of the three hall wires to Hall port: Display speed and distance
7. Any of the three motor wires to MOT port: Display speed and distance.
Above shows 3 ways to display speed and distance, you can choose one way for connection if you need this function.
Above functions also need to combine with your settings in remote, just check manual and instruction.
Recommended and Related Products:
×
$47.80$43.02
In Stock V5 Bluetooth Module Can Automatically Switch VESC Communication with Receiver or Bluetooth Module
In Stock V5 Bluetooth Module Can Automatically Switch Control VESC by Receiver or Bluetooth Module, Can Monitor and Set Parameters with VESC TOOL App on Android or IOS System.
Application: Electric skateboard, electric longboard, motorized mountainboard, efoil, surfboard, boat, etc.,
Diaplay: Voltage, current, temperature , etc.,
| Model No. | MTBLEV5 V5 Upgraded version |
| Features | With optocoupler isolation, industrial grade anti-interference, and wired long distance communication |
| Upgrade Function | It supports connection together with receiver TXD and RXD to VESC, so it can automatically switch VESC communication with receiver or bluetooth and you don't need to unplug connections. When bluetooth module connect to VESCTOOL App, it will automatically disconnect receiver TXD and TXD, really convenient. |
| With 6 LED Lights status | power, communication, data tranmission |
| Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
| Compatible Software | VESCTOOL App |
| Frequency | 2.4Ghz |
| Distance | 15m |
| Input Voltage | 3.3-24V |
| PCB Size | 46mm x 32mm |
Functions:
1. The bluetooth is developed for communication between controller and VESCTOOL via BLE, to display parameters on mobile phone, so you can monitor real time parameters on app easily.
2. Motor current, duty cycle, ERPM, motor power, motor temperature, battery voltage, battery current, MOS temperature, charging current, charging power, etc., are able to display through the bluetooth module.
3. You can adjust parameters for motor settings, Including General, BLDC, FOC, PID controllers, etc informations.
4. It supports VESCTOOL Compatible controller based on V4, V6.0, V75_300 hardware, please choose the correct hardware version of your controller, we will match compatible cable for you.
5. Firmware is updatable.
VESCTOOL Compatible Speed Controllers:
×
$141.70$23.22
In Stock Maytech Foil Boost VESC 100A V6 Speed Controller with Heat Fin for SUP Foil Esk8 Robots
| Model No. | MTSPF60100 VESC Controller |
| Input Voltage | 3-12S Lipo (12.6V-50V) |
| Hardware | VESC6.0 |
| Firmware | Updatable |
| Cont Current | 100A |
| Burst Current | 240A |
| Software | VESCTOOL Compatible |
| Heat Sink | With, attach to mosfet, better heat dissipation |
| Waterproof | No, not waterproof, please do good waterproof job if you use it for water sports |
Click Here: How to Display Volt, Current, RPM with TX and RX?
Application:
DIY foil assist on wing foil, wind surf foil, sup foil board, kite foil, hull cleaning device, underwater cleaning robot, boat cleaner, electric skateboard, drone, fighting robots, combat robots, ebike, escooter, electric bicycle, etc.,
Aiming to convert non-electric foil boards to electric foil easily with reasonable cost.
V5 Bluetooth Module:
| Model No. | MTBLEV5 V5 Upgraded version |
| Features | With optocoupler isolation, industrial grade anti-interference, and wired long distance communication |
| Upgrade Function | It supports connection together with receiver TXD and RXD to VESC, so it can automatically switch VESC communication with receiver or bluetooth and you don't need to unplug connections. When bluetooth module connect to VESCTOOL App, it will automatically disconnect receiver TXD and TXD, really convenient. |
| With 6 LED Lights status | power, communication, data tranmission |
| Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
| Compatible Software | VESCTOOL App |
| Frequency | 2.4Ghz |
| Distance | 15m |
| Input Voltage | 3.3-24V |
| PCB Size | 46mm x 32mm |
V2 Bluetooth Module:
| Model No. | MTBLEV2 V2 Version |
| With 3 LED Lights status | power, communication, database |
| Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
|
Compatible Software |
VESCTOOL App |
| Frequency | 2.4Ghz |
| ARM Processor | ARM Cortex-M0 32 bit processor 256kB flash&16kB RAM |
| PCB Size | 41mm x 21mm |
| Net Weight | 5g |
| Antenna Length | 90mm |
Recommend Products: Click below pictures to check more information
Brushless Outrunner Motors:
×
Only connect CAN L and CAN H ! GND pins and 5V should never be connected in a V6/V75 based SUPERFOC ESCs or VESC array.
$159.00$3.51
In Stock SUPERFOC6.8 50V V6.0 based Speed Controller Great FOC Function
Specification:
| Model No. | MTSPF6.8 |
| Input Voltage | 3-12S Lipo (12.6V-50V) |
| Hardware | VESC6.0 |
| Firmware | Updatable |
| Cont Current | 50A |
| Burst Current | 240A |
| Software | VESCTOOL Compatible |
| Heat Sink | Without |
| Application | Electric skateboard, elongboard, fighting robots, ebike, escooter, electric vehicles, friction drive ebike, etc., |
Notice:
Never connect one reclever to two or more V6/V75 based SUPERFOC ESCs or VESCs in an array! Permanent damage may result from Y-PPM wiring.
Only connect CAN L and CAN H ! GND pins and 5V should never be connected in a V6/V75 based SUPERFOC ESCs or VESC array.
Attention Points when you receive the Controller Please:
All products had been double checked and tested one by one before shipment, only if the products are working normally would be shipped out.
- When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
- Do not use switching power supply, the instant voltage when switching power supply connect to controller is very high, which would easy damage the controller.
- Do not push the throttle too hard when test without load, gently and slowly speed up.
- Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller.
- Please must remember to change to corresponding modes when you adjust parameters, for example, the controller default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESCTOOL didn't change to FOC mode, then when you push throttle, would easy burn the VESC, same as FOC mode.
-
In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage
ERPM= motor pole pairs number * KV * Voltage - If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
- For V4 based controller:
Do not suggest to use FOC mode, suggest to use BLDC mode.
If need to use FOC mode, then must use voltage under 20V.
- The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted
V5 Bluetooth Module:
| Model No. | MTBLEV5 V5 Upgraded version |
| Features | With optocoupler isolation, industrial grade anti-interference, and wired long distance communication |
| Upgrade Function | It supports connection together with receiver TXD and RXD to VESC, so it can automatically switch VESC communication with receiver or bluetooth and you don't need to unplug connections. When bluetooth module connect to VESCTOOL App, it will automatically disconnect receiver TXD and TXD, really convenient. |
| With 6 LED Lights status | power, communication, data tranmission |
| Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
| Compatible Software | VESCTOOL App |
| Frequency | 2.4Ghz |
| Distance | 15m |
| Input Voltage | 3.3-24V |
| PCB Size | 46mm x 32mm |
V2 Bluetooth Module:
| Model No. | MTBLEV2 V2 Version |
| With 3 LED Lights status | power, communication, database |
| Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
|
Compatible Software |
VESCTOOL App |
| Frequency | 2.4Ghz |
| ARM Processor | ARM Cortex-M0 32 bit processor 256kB flash&16kB RAM |
| PCB Size | 41mm x 21mm |
| Net Weight | 5g |
| Antenna Length | 90mm |
Recommend Products: Click below pictures to check more information
Brushless Outrunner Motors: