MTSVESC6.0 Mini 10S 42V VESC6.0 based 30A Speed Controller

  • En oferta
  • $132.90
  • Precio habitual $156.35
Los gastos de envío se calculan en la pantalla de pagos.


Maytech MTSVESC6.0M Mini VESC 35g 10S 42V VESC6.0 based Controller 30A for Combat Robots/Delivery Robots Arm Robotics/Camera Motorized Dolly / Smart Robot Lawnmower

 



Specification: 

Model No. MTSVESC6.0M Cont. Current 30A
Burst Current 50A Input Voltage 42V(10S)
Hardware Based on VESC6.0 Firmware  Updatable 
Software VESC_TOOL Compatible FOC  Yes, can work 
Size 
65mm*20mm  Compatible Motor Sensored / Sensorless Motor
Net Weight 35g/pcs

 

Function overview

- The smallest VESC based controller on the market, with a size of only 18x65mm, can be used for miniaturized equipment, such as smart cars, micro robots, electric roller skates, drones, electric models, etc.

- Based on powerful VESC software and hardware, it supports PWM analog voltage UART and USB speed signal input. It supports sensored and sensorless brushless motors and brushed motors, and supports square wave and FOC modes.

- Support up to 10S lithium battery,over‐current/over‐temperature/over‐voltage protection.

- Support VESC_TOOL, UART is enabled by default in the factory firmware. It is recommended to connect VESC through the serial port of the host computer. If you need a USB connection, you can use the random adapter cable to connect.

- Recommended matching scheme: 6S lithium battery plus MTO2830 with Hall sensoredbrushless motor.

Port Definition: 

VESC6.0 Mini Electric speed controller small size high voltage 42V fighting robots robot arm electric smart robot Lawnmower save you more space with PWM signal can use UART

- GND1/2, DP(Data postive), DM(Data Minus/Negative): USB port for programming.

- GND1/2, PPM, +5V: PPM port to connect PPM transceivers.

- SWC(CLK), SWD(DIO), GND1/2, 5V: SWD port, to get direct access to the Chipset. Diagnostics, debugging, and real time data.

- A1(ADC1), A2(ADC2), TX, RX, GND1/2, 5V: COMM port for various kinds of other communication methods like I2C, ADC, Uart. You can use your Arduino or Raspberry Pi to control the VESC.

- 5V, TEMP, HAll1, Hall2, Hall3 GND: Sensor port for motor Hall sensors (ABI, HALL, magnetic precision encoders).

-DP on the pin refers to Data Positive. DM refers to Data Minus. It is necessary to connect to the computer by making a USB adapter. The standard USB port has four wires: two power supplies positive and negative, and two data positive and negative. Players only need to connect the power negative (GND) and data positive and negative three wires to the computer USB port, no need to connect the power positive supply.

PS: (GND1 and GND2 are same, for above ports containing GND1/2, you can just select one to use).

 

VESC6.0 Mini Electric speed controller small size high voltage 42V fighting robots robot arm electric smart robot Lawnmower save you more space with PWM signal can use UART


VESC6.0 Mini Electric speed controller small size high voltage 42V fighting robots robot arm electric smart robot Lawnmower save you more space with PWM signal can use UART

Application:  Electric roller skates, Smart cars, Electric mode cars/boat/tank, Micro robot arm, Fighting robots, Micro robots, Drones, etc.,

Hardware Overview:

- 4-layers 3OZ PCB, main power loop adds copper bars to reduce resistance.

- Use Swiss STM32F405RT6 to ensure strong computing power

- 3-channel independent driver chip LM5113SDE (WSON package 4mm*4mm) from American TI (Texas Instruments) company, can withstand 100V.

- 6pcs ON’s 60V/2.4 milliohm NTMFS5C628NLT1G MOSFET, DFN 5.5mm*6mm, theoretically each MOS can withstand 150A peak current.

- 3pcs Current Sense Resistor from CSS2H-2512R-L500, 0.5 milliohm copper-manganese alloy resistors, can withstand max 100A peak current.

- 3pcs Current Sense Amplifier from AD (Analog Devices) company, Model AD8417BRMZ, small size high accuracy, with low temperature drift coefficient.

- Main DC-DC chip is LMR16006 from American TI company, convert high voltage (Under 60V) to 5V, max output 0.6A.

- Slave DC-DC chip is MCP1700T-3302E/TT from Microchip company, convert 5V to 3.3V power for components.

- 56pcs 2u2 100V high voltage chip capacitor, with 123.2μf gross capacity.


Attention Points when you receive the VESC Please:

All products had been double checked and tested one by one before shipment, only if the products are working normally would be shipped out. 

  • When you receive the VESC, please test without load and do not connect motor, first check if the VESC can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
  • Do not use switching power supply, the instant voltage when switching power supply connect to VESC is very high, which would easy damage the VESC.
  • Do not push the throttle too hard when test without load, gently and slowly speed up.
  • Be cautious when adjust parameters, if parameters set mistake, would also easy damage the VESC.
  • Please must remember to change to corresponding modes when you adjust parameters, for example, the VESC default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESC_TOOL didn't change to FOC mode, then when you push throttle, would easy burn the VESC, same as FOC mode.
  • In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage 
    ERPM= motor pole pairs number * KV * Voltage
  • If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
  • For V4 based VESC:

          Do not suggest to use FOC mode, suggest to use BLDC mode. 
          If need to use FOC mode, then must use voltage under 20V.

  • The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted


    Related Products: (Click the following pictures to check more products)

    Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes 

    In Stock Maytech New Remote for Electric Skateboard MTSKR2005WF V2 Waterproof Hand Remote

    Maytech Brushless Outrunner Sensored Motors

    Maytech brushless outrunner motor for electric skateboard 6355/6374/6365.6880/6396 sensored brushless engines

    Maytech VESC_TOOL Compitable VESC:

    Maytech Benjamin Vedder bruhsless VESC electric speed controller SUPER ESC dual vesc