New 6374 170KV DC Motor C4 8mm Shaft with Stainless Steel Cooling Mesh for Electric Skateboard

In Stock Maytech Electric Skateboard Splashproof Remote Control MTSKR2005WF IP66 2.4GHZ

Maytech MTSKR2005WF IP66 Splashproof Esk8 Remote Electric Skateboard Elongboard Hand Remote with 3 Speed Modes

If you want to use for water sports, then please order our MTSKR1905WF IP67 waterproof remote Here>

In Stock Brushless 6374 Sealed Motor 10mm Shaft Sensored 170/190KV

Maytech Brushless 6374 170/190KV Closed Cover Outrunner Sensored Motor 10mm Shaft IP54 Splash Waterproof Motor for Esk8/E-bike MTO6374-HA-C2

Model No	MTO6374-HA-C2	KV	170/190
Idle Current	0.8A	Max Current	65A
Inpur Voltage	2-12s Lipo	Max Output Watt	3550W
Max Pull	13000g	Rated Current	60A
Motor Weight	860g	Shaft	10mm
Output Shaft Length	34mm	Internal Resistance	0.0402

Motor Drawing: 

Stock Notice Before Place Order:

1. The motor 170KV is stock item, but stock is limited, so please confirm your order asap, or please contact us agnes@maytech.cn to check stock first if you need very urgently.

90KV and 190KV are not stock item, lead time is about 35-50 days if you need this KV or other KV. 

2. Shipping time is about 24 working hours after your order confirmed if the product you ordered is in stock, if not in stock, lead time is about 30-40 days.

3. Motor wire leads out position is specific, if wind one more circle or one less circle, the KV would differ much, hard to make exact KV, so each motor might has ±5%-10% tolerance, this is normal.

Related Products: (Click the following pictures to check more products)

Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes 

 

Maytech Brushless Outrunner Sensored Motors

 

Maytech VESC_TOOL Compitable Controller:

 

In Stock Brushless 6374 Unsealed Motor 8mm Shaft Sensored 90/190KV

Maytech Brushless 6374 190KV Open Cover Outrunner Sensored Motor for Esk8/E-bike/Fighting Robots/Mountainboard/E-scooter

Notice: 

The motor has upgraded hall sensor embedded into stator, hall sensor board is more stable and motor has more precise positioning and smoother startup. 

Printing on the motor case also has updated to with CE & ROHS symbol. 

The upgraded version can work with previous version in same KV. 

New embeded hall sensor version VS old version:

1. New version is with embedded hall sensor to stator:
Hall sensor board is more stable and motor has more precise positioning and more smooth starup.

2. With changing the hall sensor position, inside space is bigger than before and the original small bearing inside the stator can be replaced with a larger model, which increases the lifetime of the motor.

3. Mounting holes are updated to 8x M4 with deeper thread 11mm. Motor installation will be firmer.

Motor Drawing: 

Related Products: (Click the following pictures to check more products)

Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes 

Maytech Brushless Outrunner Sensored Motors

Maytech VESC_TOOL Compitable controller:

Maytech MTSKR1712 Small and Light Cheap Remote:

In Stock Maytech Foil Boost VESC 100A V6 Speed Controller with Heat Fin for SUP Foil Esk8 Robots

In Stock SUPERFOC6.8 50V V6.0 based Speed Controller Great FOC Function

Specification:

Notice: 

Attention Points when you receive the Controller Please:

All products had been double checked and tested one by one before shipment, only if the products are working normally would be shipped out. 

• When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
• Do not use switching power supply, the instant voltage when switching power supply connect to controller is very high, which would easy damage the controller.
• Do not push the throttle too hard when test without load, gently and slowly speed up.
• Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller.
• Please must remember to change to corresponding modes when you adjust parameters, for example, the controller default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESCTOOL didn't change to FOC mode, then when you push throttle, would easy burn the VESC, same as FOC mode.
• In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage
  ERPM= motor pole pairs number * KV * Voltage
• If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
• For V4 based controller:

          Do not suggest to use FOC mode, suggest to use BLDC mode. 
          If need to use FOC mode, then must use voltage under 20V.

• The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted

V5 Bluetooth Module: 

V2 Bluetooth Module: 

Recommend Products: Click below pictures to check more information

Brushless Outrunner Motors: 

In Stock MTS1810AS 180A Anti-spark Switch Protection for ESC Battery

MTS1810AS Anti-spark Switch with On and Off for Electric Skateboard/Mountainboard/Ebike/E-scooter/Fighting Robots/Lawnmower Robots

Maytech Anti-spark on-off power switch board MTS1810AS for VESCTOOL Compatible controller

Function: To protect your controller and battery, eliminate surge current when startup and speed up, because when startup and speed up surge current would be bery high, the antispark switch is protection function. 

Anti spark on-off switch for electric skateboard, longboard, bike, scooter e.t.c. Same function as Vedder Anti-Spark.

This switch is a small, efficient, safe and reliable way to power on/off your DIY Electric Skateboard. When doing this, it also protects delicate components (such as the VESC or other ESC's) from unwanted power surges. This anti Spark Switch is recommended to anyone looking to build the ultimate DIY Electric Longboard. 

Electric Skateboard Power Switch ON OFF DIY Switch Anti-Spark High Voltage High Amp 100A 6v-50v Electric Longboard.

Related Products: (Click the following pictures to check more products)

Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes 

Maytech Brushless Outrunner Sensored Motors

Maytech VESCTOOL Compitable Controller:

Maytech MTSKR1712 Small and Light Cheap Remote: