Maytech MTSKR2005WF New Remote Instruction

BLDC mode, brake mode, brushless dc motor for sale, brushless motor DIY electric skateboard, canbus connection, charging pad, compatible to VESC and ESC, Compatible with sensored or sensorless motor, controller for Electric skateboard, controller for Esk8, current showing, dc motor speed control board design, display function, display screen, drivetrains, dual motor driven electric skateboard, dust-proof, dustproof motor, E-bike, e-scooter, Electirc speed controller, electric bike, Electric kayak motors, electric motor for power tools, electric outboard engine, electric outboard motors, electric scooter, electric skating, electric SUP motors, Esk8, Esk8 mode, Eskate, eskating, Esurf mode, FOC mode, gear build system motor, general motor, Great start-up, hand remote, hand remote control, high quality components construction, motor climb, motor mount, motor surfboard, motorized skateboard, motorized. Mounted motor, MTSKR1805WF waterproof remote, MTSKR1905WF fully waterproof remote, outrunner motor with direct drive, paramters showing, powerful engine, PPM signal, programmable VESC, PWM signal format, remote control, remote controller, robotic motor, scooter, sealed cover motor, show distance, show rpm, show speed, show temp, single motor for skateboard, single shaft motor, skating, small high power electric motor, speed controller, speed up and speed down, splash waterproof, splash waterproof motor, splsh proof motor, SUPER esc, SUPER FOC mode, temperature, throttle system, torque monster, underwater brushless motor, updatable vesc, upgraded remote, V1 remote, VESC benjamin vedder controller, VESC controller, VESC6.0 based controller, VESC_TOOL compatible controller, watreproof motor, wirelsss charging -

Maytech MTSKR2005WF New Remote Instruction

Pre-sale Maytech New Remote for Electric Skateboard MTSKR2005WF V2 Waterproof Hand Remote

1. Remote Apperance:

Electric skateboard, Esk8, Electric longboard, Elongboard, Electric board Electric mountainboard, all terrain offroad skateboard, Eskate, skateboard, outdoor skateboard, motorized skateboard, motorized board, motorized mountianboard, powered skateboard, city skateboard, street skateboard, hover board, E-bike, electric bike, electric bicycle, electric scooter, e-scooter, e-mountainbike, electric mountainbike, electric vehicles, electric tools, offroad skateboard, long board, e-skateboard, esk8 board, outdoor sport skateboard

OEM skateboard, eboard, electric skateboard propulsion configuration, motorcycle, torqueboards, heat pump control board, advanced electric skateboard , 100% Eco-Friendly, Wireless Control, Rapid Charging, All Terrain, direct drive electric skateboard , speed boards, cruiser board, hybrid board, electric skateboarding , electric skate, hybrid skateboarding, commercial belt driven boards, wood skateboard, Synthetic, compound, belt-driven motor skateboard, hub motor drived skateboard,  Hill climb skateboard, powerful skateboard, Electric motorcycle, parking system,  ROV, printing device, drone, multi-copter,  multi-rotor, helicopter, airplace, rc fight, rc airplane, rc drone, rc car,

2. Receiver wiring instruction with VESC or VESC based Controllers: 

There's 2 ways to connect receiver and VESC:

1. Connect VESC signal cable to receiver PWM; 5V; GND (as above receiver pin definition)

2. You can also use UART: 

  • Cross connection of Receiver TXD/RXD and VESC RX/TX: Receiver’s TXD>> VESC RX;Receiver RXD>> VESC TX, 5V and GND also need to be connected, better use stranded wire, wire length should be shorter than 20cm.
  • VESC supports UARR and PWM(PPM) throttle control. When use with Maytech waterproof remote, you can select PPM and UART, and select corresponding control in remote (“Data Source” and “VESC Thr”). PPM to control throttle and UART to read voltage/current/ temperature/speed/etc.
  • Please set “Baudrate” to “115200 bps” in VESC_TOOL.

VESC_TOOL electric speed controller benjamin vedder VESC controller VESC6.12 VESC6.0 VESC4.12 V4 SUPER ESC

3. Pairing:

Maytecch new remote MTSKR2005WF IP67 waterproof hand remote controller for electric skateboard elongboard mountainboard Esk8 eskate onlyMTSKR1805WF waterproof remote , MTSKR1905WF fully waterproof remote ,remote controller , hand remote  , remote control  , V1 remote  , upgraded remote  , hand remote control  , throttle system  , brake mode  , Esk8 mode  , Esurf mode  , speed up and speed down , wirelsss charging , charging pad  , display function  , display screen , paramters showing  , current showing  , temperature , show speed  , show rpm  , show distance  , show temp  , PWM signal format  , PPM signal  , compatible to VESC and ESC ,

  1. If remote and receiver are paired successfully before, then no need to pair them again.

  2. If remote and receiver does not get paired before, please pair them according to below steps:

1) Turn off receiver.

2) Select【>4.Pair】and long press function button for 1 second to enter pair status. When screen shows

【Paring…】, turn on receiver and it will auto-pair with remote control in 0.5 second. Red led lights steady. Pairing competed. Remote screen will automatically return to main menu. If auto-pairing time is over 1 second and screen still shows【Pairing…】, pairing fails and it needs to turn off and turn on receiver again to pair them. If you don’t want to continue the pairing process, long press function button to exit to main menu.

4. Calibration

Due to environmental changes during use, remote calibration may be out of proportion to the output of PWM signal. Then it needs to do calibration.

Select 【 >5.Calibration 】 and long press function button for 1 second to enter Sub-menu. Once enter calibration, it must need to be finished. If don’t continue calibration and exit, remote and receiver will stop working together.

Press throttle trigger to top and loose it. Then press brake trigger to top and loose. When press trigger, the screen will prompt【Calibrating】 and 【 Cal. OK】.

After both two are【 Cal. OK】, long press function button to return to main menu

 

 

 

 

 

 

 


Tags