Maytech.cn
In Stock MTSPF6.6K 200A V6 Based Controller 12S 50V SUPERFOC ESC
In Stock MTSPF6.6K 200A V6 Based Controller 12S 50V SUPERFOC ESC
Impossibile caricare la disponibilità di ritiro
Specification:
Model No. | MTSPF6.6K |
Input Voltage | 3-12S Lipo (12.6V-50V) |
Hardware | VESC6.0 |
Firmware | Updatable |
Cont Current | 200A |
Burst Current | 240A |
Software | VESCTOOL Compatible |
Heat Sink | With |
Application | Electric skateboard, elongboard, fighting robots, ebike, escooter, electric vehicles, friction drive ebike, etc., |
Only connect CAN L and CAN H ! GND pins and 5V should never be connected in a V6/V75 based SUPERFOC ESCs or VESC array.





-
- When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
- Do not use switching power supply, the instant voltage when switching power supply connect to controller is very high, which would easy damage the controller.
- Do not push the throttle too hard when test without load, gently and slowly speed up.
- Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller.
- Please must remember to change to corresponding modes when you adjust parameters, for example, the VESC default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESCTOOL didn't change to FOC mode, then when you push throttle, would easy burn the controller, same as FOC mode.
-
In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage
ERPM= motor pole pairs number * KV * Voltage - If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
- For V4 based controller:
Do not suggest to use FOC mode, suggest to use BLDC mode.
If need to use FOC mode, then must use voltage under 20V.- The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted
V5 Bluetooth Module:
Model No. | MTBLEV5 V5 Upgraded version |
Features | With optocoupler isolation, industrial grade anti-interference, and wired long distance communication |
Upgrade Function | It supports connection together with receiver TXD and RXD to VESC, so it can automatically switch VESC communication with receiver or bluetooth and you don't need to unplug connections. When bluetooth module connect to VESCTOOL App, it will automatically disconnect receiver TXD and TXD, really convenient. |
With 6 LED Lights status | power, communication, data tranmission |
Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
Compatible Software | VESCTOOL App |
Frequency | 2.4Ghz |
Distance | 15m |
Input Voltage | 3.3-24V |
PCB Size | 46mm x 32mm |
V2 Bluetooth Module:
Model No. | MTBLEV2 V2 Version |
With 3 LED Lights status | power, communication, database |
Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
Compatible Software |
VESCTOOL App |
Frequency | 2.4Ghz |
ARM Processor | ARM Cortex-M0 32 bit processor 256kB flash&16kB RAM |
PCB Size | 41mm x 21mm |
Net Weight | 5g |
Antenna Length | 90mm |
Recommend Products: Click below pictures to check more information
Share













0
Articoli totali
$0.00
Subtotale prodotto
😍 Handpicked Recommendations
- In Stock 2pcs / 5pcs MTSPF7.12K V2 Max 75V 200A V75/300 based Speed Controller SUPERFOC ESC
$1,136.90 - +
- Maytech 200A Waterproof Watercooled VESC based on V75/300 for Efoil Electric Hydrofoil
$368.00 - +
- In Stock Brushless 6880 Sealed Motor 10mm Shaft Sensored 70KV 190KV with Big Ball Bearing
$109.80 - +
- In Stock Maytech Electric Skateboard Splashproof Remote Control MTSKR2005WF IP66 2.4GHZ
$76.90 - +
- In Stock MTS1810AS 180A Anti-spark Switch Protection for ESC Battery
$21.50 - +
- In Stock V5 Bluetooth Module Can Automatically Switch VESC Communication with Receiver or Bluetooth Module
$47.80

In Stock 2pcs / 5pcs MTSPF7.12K V2 Max 75V 200A V75/300 based Speed Controller SUPERFOC ESC
Maytech Upgraded High Current 200A Speed Controller VESCTOOL Compatible based on V75/300 Speed Controller Comb with 20W Cooling Fan and 12V DC-DC Module for Esk8/Fighting Robots
2 Options:
Specification:
Model No. | MTSPF7.12K | Dust-proof | Yes |
Cont Current | 200A | Splash Waterproof | Yes |
Software | VESC_TOOL | BEC | 5V/1.5A |
Input Volt |
18-75V If do not use brake, can use max to 75V, if use brake, please use no exceed 50V. |
PCB Size | 92*52*22mm |
Hardware | Based on V75_300 | Firmware Updatable | Yes |
Case Size | 98.5*56*35mm |
PCB Net Weight | 160g |
Fan Power | 20W | UBEC | 75V convert to 12V, power for cooling fan |
Feature |
12pcs mosfets; 8-layer PCB; separate high current components and low-curent components to two PCBs; etc |
Application | Electric skateboard, mountainboard, elongboard, all terrain skateboard, fighting robots, combat robots, walking robots, ROV, Esurf, Efoil, foilsurf, jetski, electric hydrofoil, etc., |
Notice:
Never connect one reclever to two or more V6/V75 based SUPERFOC ESCs or VESCs in an array! Permanent damage may result from Y-PPM wiring.
Only connect CAN L and CAN H ! GND pins and 5V should never be connected in a V6/V75 based SUPERFOC ESCs or VESC array.
Motor Current Max: ≤200A (According to your motor current)
Absolute Maximum Current: 250A (According to your motor current)
Battery Current Max: ≤100A (According to your battery discharge current)

Port definations:
- Type C USB port to connect computer for programming;
- LED Port for connecting customer’s LED light to show ESC is on or off;
- Sensor port for motor Hall sensors (ABI, HALL, magnetic precision encoders);
- CAN Port for CAN communication with other devices and controller arrays;
- COMM port for various kinds of other communication methods like I2C, ADC, Uart,You can use your Arduino or Raspberry Pi to control the SuperESC!
- PPM port to connect PPM transceivers.
Features:
- High voltage 18S, High curent 200A, tiny size and compact design, light weight.
- Superior Safety: With over-current protection, over-voltage protection, over-heat protection.
- 2pcs PCBs to separate high and low power components (more stable and reliable).
- 8-layer 3oz PCB Board, 3.4mm thick, supports high current and has efficient heat-dissipation capability. (Other brand PCB is only 1-2mm thick).
- 12pcs high quality Mosfets, greater efficiency, handle higher current.
- ARM 32bit processor, faster data transfer and storage.
- 3pcs Capacitors 63V 820μf, prevent power circuit impact.
- 3pcs Current sampling chips, It can make the current sampling faster and more accurate, and has a good improvement on the FOC and over-current protection functions.
- 6061 Premium Alu-Alloy Case, Quick heat-dissipation, Sleek aluminum finish, comfortable hand-feeling.
- Removable cooling fan, 20W high power for quick cooling. Ensure reliable performance with excellent temperature control technology
- USB Type C port- easy to connect and program settings.
- Firmware standard: VESCTOOL automatically recognizes this ESC as 7.5_300. This firmware can be used.
Features:
- High voltage: If use current mode, without brake, max voltage is 75V; If use current mode with brake or duty cycle mode, max voltage is 12S lipo (Max 50.4V).
- High current: 200A
- Compatible with brushed and brushless motors, intrunner and outrunner motors Sensored or Sensorless operation + Hybrid mode
- Adjustable Forward/Backward/Brake
- Regenerative Braking Function
- Configurable RPM, Current, Voltage and Power limits
- Support PPM, Analog (ADC), UART, Canbus input
- Communication ports: USB, CAN, UART
-
Support FOC sine wave mode
-
Throttle curve and ramping for all input sources
- Seamless 4-quadrant operation
- Motor Revolution, Amp Hour, Watt Hour counting
- Real time data analysis and read out via communication ports
- Adjustable protection against:
Max Motor Current and Input(Battery) Current limits
Max ERPM(RPM) (separate limits for each direction)
Max Power (Wattage)
Max Motor and ESC Temperature
Max Regenerative Braking Current (separate limits for the motor and the input)
Attention Points when you receive the controller Please:
- When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
- Do not use switching power supply, the instant voltage when switching power supply connect to controlleris very high, which would easy damage the controller.
- Do not push the throttle too hard when test without load, gently and slowly speed up.
- Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller.
- Do not recommend to work with BLDC mode, please use FOC mode.
- If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
Above notices are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted.
Related Products: Click the following pictures to check specs
Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes
Maytech Brushless Outrunner Sensored Motors
Maytech VESCTOOL Compitable SuperESC:
Application:
Electric skateboard, Esk8, Eskate, Elongboard, Mountainboard, Offroad skateboad, All terrain skateboard, Eskate, E-bike, Electric bike, Electirc motorcycle, E-scooter, Electric scooter, motorized skateboard, ROV/RPVEE, Remote operated vehicles, underwater robots, Underwater robotics, Underwater remotely operated vehicles, Subsea robots, Cablecam, Cable camera, Broadcast, IBC2019, Ultra drones, Security monitoring robots, Robots for security and safety monitoring in harsh terrain, Agile robots, SAutonomous agile robots, Security robots, Autonomously monitor security, Combat robots, Fighting robots, Electric surfboard, Efoil, etc.,

Maytech 200A Waterproof Watercooled VESC based on V75/300 for Efoil Electric Hydrofoil
Maytech 200A Waterproof Watercooled VESC based on V75/300 for Efoil Electric Hydrofoil Underwater Scooter Water Sports with waterproof junction box for wiring
Overview:
Specification:
Model No. | MTSPF7.12K-WP | Watercooled | Yes |
Current | 200A | Waterproof | Yes |
Software | VESC_TOOL | BEC | 5V/1.5A |
Input Volt |
18-75V If do not use brake, can use max to 75V, if use brake, please use no exceed 50V. |
PCB Size | 92*52*22mm |
Hardware | Based on V75_300 | Firmware Updatable | Yes |
Case Size | As picture | Net Weight | 130g/pcs |
Feature |
12pcs mosfets; 8-layer PCB; separate high current components and low-curent components to two PCBs; etc |
Application | Efoil, electric hydrofoil, foilboard, SUP board, underwater scooter, foil assist system, outboard, sea scooter, hydrofoil bike, etc., |
Notice:
Never connect one reclever to two or more V6/V75 based SUPERFOC ESCs or VESCs in an array! Permanent damage may result from Y-PPM wiring.
Only connect CAN L and CAN H ! GND pins and 5V should never be connected in a V6/V75 based SUPERFOC ESCs or VESC array.
The waterproof process is our engineer manually make, the process time is about 10-15 working days after order confirmed.
Motor Current Max: ≤200A (According to your motor current)
Absolute Maximum Current: 250A (According to your motor current)
Battery Current Max: ≤100A (According to your battery discharge current)

Features:
- High voltage 18S, High curent 200A, tiny size and compact design, light weight.
- Superior Safety: With over-current protection, over-voltage protection, over-heat protection.
- 2pcs PCBs to separate high and low power components (more stable and reliable).
- 8-layer 3oz PCB Board, 3.4mm thick, supports high current and has efficient heat-dissipation capability. (Other brand PCB is only 1-2mm thick).
- 12pcs high quality Mosfets, greater efficiency, handle higher current.
- ARM 32bit processor, faster data transfer and storage.
- 3pcs Capacitors 63V 820μf, prevent power circuit impact.
- 3pcs Current sampling chips, It can make the current sampling faster and more accurate, and has a good improvement on the FOC and over-current protection functions.
- 6061 Premium Alu-Alloy Case, Quick heat-dissipation, Sleek aluminum finish, comfortable hand-feeling.
- Removable cooling fan, 20W high power for quick cooling. Ensure reliable performance with excellent temperature control technology
- USB Type C port- easy to connect and program settings.
- Firmware standard: VESCTOOL automatically recognizes this ESC as 7.5_300. This firmware can be used.
Features:
- High voltage: If use current mode, without brake, max voltage is 75V; If use current mode with brake or duty cycle mode, max voltage is 12S lipo (Max 50.4V).
- High current: 200A
- Compatible with brushed and brushless motors, intrunner and outrunner motors Sensored or Sensorless operation + Hybrid mode
- Adjustable Forward/Backward/Brake
- Regenerative Braking Function
- Configurable RPM, Current, Voltage and Power limits
- Support PPM, Analog (ADC), UART, Canbus input
- Communication ports: USB, CAN, UART
-
Support FOC sine wave mode
-
Throttle curve and ramping for all input sources
- Seamless 4-quadrant operation
- Motor Revolution, Amp Hour, Watt Hour counting
- Real time data analysis and read out via communication ports
- Adjustable protection against:
Max Motor Current and Input(Battery) Current limits
Max ERPM(RPM) (separate limits for each direction)
Max Power (Wattage)
Max Motor and ESC Temperature
Max Regenerative Braking Current (separate limits for the motor and the input)
Attention Points when you receive the controller Please:
- When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
- Do not use switching power supply, the instant voltage when switching power supply connect to controlleris very high, which would easy damage the controller.
- Do not push the throttle too hard when test without load, gently and slowly speed up.
- Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller.
- Do not recommend to work with BLDC mode, please use FOC mode.
- If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
Above notices are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted.
Related Products: Click the following pictures to check specs
Maytech MTSKR1905WF waterproof remote for water sports: In stock
Maytech VESCTOOL Compitable SuperESC:
Application:
Electric skateboard, Esk8, Eskate, Elongboard, Mountainboard, Offroad skateboad, All terrain skateboard, Eskate, E-bike, Electric bike, Electirc motorcycle, E-scooter, Electric scooter, motorized skateboard, ROV/RPVEE, Remote operated vehicles, underwater robots, Underwater robotics, Underwater remotely operated vehicles, Subsea robots, Cablecam, Cable camera, Broadcast, IBC2019, Ultra drones, Security monitoring robots, Robots for security and safety monitoring in harsh terrain, Agile robots, SAutonomous agile robots, Security robots, Autonomously monitor security, Combat robots, Fighting robots, Electric surfboard, Efoil, etc.,

In Stock Brushless 6880 Sealed Motor 10mm Shaft Sensored 70KV 190KV with Big Ball Bearing
Maytech Brushless 6880 70KV 190KV Closed Cover Sensored Dustproof and Waterproof Motor for Esk8/E-bike/Robots/Mountainboard/E-scooter MTO6880-190-HA-C3 With big ball bearing
Stock motor has 2 printing type as in the picture, will ship randomly if order 1pcs.
If order ≥2pcs, will ship same type.
Model No
|
MTO6880-190-HA-C3 |
KV
|
70/ 190 |
Idle Current
|
0.8A
|
Max Current
|
65A
|
Inpur Voltage
|
2-12s Lipo
|
Max Output Watt
|
3550W
|
Max Pull
|
13000g
|
Rated Current
|
60A
|
Motor Weight
|
1200g
|
Shaft
|
10mm
|
Output Shaft Length
|
45.5mm
|
Internal Resistance
|
0.0402
|
Stock Notification:
Our standard stock KV is 190KV, 70KV is not stock item, lead time is about 35-45 days after your order confirmed if you order 70KV.


Original Version Motor Drawing:

6880 Motor Drawing Updated for for new batch with embeded hall sensor:
New updated 6880 motor features VS old version:
1. New version is with embedded hall sensor to stator:
Hall sensor board is more stable and motor has more precise positioning and more smooth starup.
2. With changing the hall sensor position, inside space is bigger than before and the original small bearing inside the stator can be replaced with a larger model, which increases the lifetime of the motor.
3. Mounting holes are updated to 8x M4 with deeper thread 11mm. Motor installation will be firmer.
Stock Notice Before Place Order:
1. The motor is stock item, but stock is limited, so please confirm your order asap, or please contact us agnes@maytech.cn to check stock first if you need very urgently.2. Shipping time is about 24 working hours after your order confirmed if the product you ordered is in stock, if not in stock, lead time is about 30-40 days.
3. Motor wire leads out position is specific, if wind one more circle or one less circle, the KV would differ much, hard to make exact KV, so each motor might has ±5%-10% tolerance, this is normal.
Related Products: (Click the following pictures to check more products)
Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes
Maytech Brushless Outrunner Sensored Motors
Maytech VESC_TOOL Compitable Controller:
Maytech MTSKR1712 Small and Light Cheap Remote:

In Stock Maytech Electric Skateboard Splashproof Remote Control MTSKR2005WF IP66 2.4GHZ
Maytech MTSKR2005WF IP66 Splashproof Esk8 Remote Electric Skateboard Elongboard Hand Remote with 3 Speed Modes
If you want to use for water sports, then please order our MTSKR1905WF IP67 waterproof remote Here>
Specifications:
Model No. | MTSKR2005WF (MTSKR20WFV2) |
Waterproof Rank | IP66 splashproof |
Speed Display | Yes |
Throttle and brake Display | ±100% |
Speed Mode |
3 speed modes, each mode can adjust speed from 1%-100% throttle |
Charger |
QC 2.0 wireless |
Display Screen |
OLED yellow & blue screen |
Throttle and Brake Signal Output Range |
1.5ms-2ms for throttle; 1.5ms-1ms for brake |
Voltage Display |
Remote & main battery voltage level (lithium iron; lithium ion battery optional) |
Telemeter Data by Receiver |
Motor RPM; main battery voltage |
Telemeter Data by VESC | ESC voltage/ current/ temp; Motor temp/ RPM |
Triggers | 2x high senstive triggers |
Wireless Frequency | 2.4GHz wireless with 40 channels |
VESC Control Mode | Duty Cycle/ Current Mode |
Travel Mileage | Yes |
Receiver Built-in Switch for Esk8 Light / Esurf Water Pump |
1x 30V 3A mechanical relay switch; 1x 20V 2A transistor electronic switch |
Accessories | Wireless charging pad; receiver; 3pcs dupont cable |
Compatible ESCs | VESCTOOL/ Focbox/ Other PWM ESCs that has same signal output range with the remote |
Application | Only for Electric skateboard, elongboard, mountainboard |
Features:
1. Display speed (km/h or mph) in Esk8 mode (for electric skateboard)2. Display voltage in V, current, temperature when work with VESC based controller
> Get Manual: Remote Manual and Instruction
2. The receiver is not waterproof, please keep the receiver away from water, otherwise the receiver would easy to have short circuit problem.
3. Please attention when weld wire on the receiver or when using, each 2 pins do not touch each other, otherwise would easy to burn the receiver.

In Stock MTS1810AS 180A Anti-spark Switch Protection for ESC Battery
MTS1810AS Anti-spark Switch with On and Off for Electric Skateboard/Mountainboard/Ebike/E-scooter/Fighting Robots/Lawnmower Robots
Maytech Anti-spark on-off power switch board MTS1810AS for VESCTOOL Compatible controller
Function: To protect your controller and battery, eliminate surge current when startup and speed up, because when startup and speed up surge current would be bery high, the antispark switch is protection function.
Anti spark on-off switch for electric skateboard, longboard, bike, scooter e.t.c. Same function as Vedder Anti-Spark.
This switch is a small, efficient, safe and reliable way to power on/off your DIY Electric Skateboard. When doing this, it also protects delicate components (such as the VESC or other ESC's) from unwanted power surges. This anti Spark Switch is recommended to anyone looking to build the ultimate DIY Electric Longboard.
Electric Skateboard Power Switch ON OFF DIY Switch Anti-Spark High Voltage High Amp 100A 6v-50v Electric Longboard.
Model No. |
MTS1810AS |
Dimension |
48mm(L)*22.5mm(W) *5.0(H) |
Current |
180A |
Voltage |
50V |
Power side Cable |
10# 160mm Red and black |
Switch Cable |
30tin 160mmwith 4pin JR male plug |
Related Products: (Click the following pictures to check more products)
Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes
Maytech Brushless Outrunner Sensored Motors
Maytech VESCTOOL Compitable Controller:
Maytech MTSKR1712 Small and Light Cheap Remote:

In Stock V5 Bluetooth Module Can Automatically Switch VESC Communication with Receiver or Bluetooth Module
In Stock V5 Bluetooth Module Can Automatically Switch Control VESC by Receiver or Bluetooth Module, Can Monitor and Set Parameters with VESC TOOL App on Android or IOS System.
Application: Electric skateboard, electric longboard, motorized mountainboard, efoil, surfboard, boat, etc.,
Diaplay: Voltage, current, temperature , etc.,
Model No. | MTBLEV5 V5 Upgraded version |
Features | With optocoupler isolation, industrial grade anti-interference, and wired long distance communication |
Upgrade Function | It supports connection together with receiver TXD and RXD to VESC, so it can automatically switch VESC communication with receiver or bluetooth and you don't need to unplug connections. When bluetooth module connect to VESCTOOL App, it will automatically disconnect receiver TXD and TXD, really convenient. |
With 6 LED Lights status | power, communication, data tranmission |
Compatible Controller Hardware | V4 / V6 / V75 based SuperESC |
Compatible Software | VESCTOOL App |
Frequency | 2.4Ghz |
Distance | 15m |
Input Voltage | 3.3-24V |
PCB Size | 46mm x 32mm |
