Brushless 6355 Sealed Motor 10mm Shaft Sensored 170KV

In Stock SUPERFOC6.8 50V V6.0 based Speed Controller Great FOC Function

Specification:

Notice: 

Attention Points when you receive the Controller Please:

All products had been double checked and tested one by one before shipment, only if the products are working normally would be shipped out. 

• When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
• Do not use switching power supply, the instant voltage when switching power supply connect to controller is very high, which would easy damage the controller.
• Do not push the throttle too hard when test without load, gently and slowly speed up.
• Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller.
• Please must remember to change to corresponding modes when you adjust parameters, for example, the controller default mode is BLDC mode, but if you want to detect FOC mode and adjusted FOC parameters, at this time if mode in VESCTOOL didn't change to FOC mode, then when you push throttle, would easy burn the VESC, same as FOC mode.
• In FOC mode, ERPM suggest to control in 30000-40000; In BLDC moed, ERPM suggest to control in 50000-60000, otherwise driver IC would easy to be damaged. ERPM= motor pole pairs number * KV * Voltage
  ERPM= motor pole pairs number * KV * Voltage
• If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
• For V4 based controller:

          Do not suggest to use FOC mode, suggest to use BLDC mode. 
          If need to use FOC mode, then must use voltage under 20V.

• The above are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted

V5 Bluetooth Module: 

V2 Bluetooth Module: 

Recommend Products: Click below pictures to check more information

Brushless Outrunner Motors: 

In Stock Brushless 6355 Sealed Motor 8mm Shaft Sensored 170/190KV

Maytech Brushless 6355 170/190KV 8mm Shaft Closed Cover Outrunner Sensored Motor IP54 Splash Waterproof for Esk8/Robotics/E-bike/E-scooter/Mountainboard/Offroad Board

 

Stock Notification: 

Our standard stock KV is 170KV and 190KV, 70KV is not stock item, lead time is about 35-45 days after your order confirmed if you order 70KV. 

Notice: 

The motor has upgraded hall sensor embedded into stator, hall sensor board is more stable and motor has more precise positioning and smoother startup. 

Printing on the motor case also has updated to with CE & ROHS symbol. 

The upgraded version can work with previous version in same KV. 

 

Stock Notice Before Place Order:

Related Products: (Click the following pictures to check more products)

Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes 

Maytech Brushless Outrunner Sensored Motors

Maytech VESC_TOOL Compitable Controller:

Maytech MTSKR1712 Small and Light Cheap Remote:

In Stock Brushless 6355 Unsealed Motor 8mm Shaft Sensored 170KV

Maytech Brushless 6355 170KV Open Cover Outrunner Sensored Motor for Esk8/E-bike/Robots/Mountainboard/E-scooter

Notice: 

The motor has upgraded hall sensor embedded into stator, hall sensor board is more stable and motor has more precise positioning and smoother startup. 

Printing on the motor case also has updated to with CE & ROHS symbol. 

The upgraded version can work with previous version in same KV. 

Motor Drawing:

Related Products: (Click the following pictures to check more products)

Maytech MTSKR2005WF New Waterproof Remote for Esk8 Only with 3 Speed Modes 

 

Maytech Brushless Outrunner Sensored Motors

 

Maytech VESC_TOOL Compitable Controller:

Maytech MTSKR1712 Small and Light Cheap Remote:

 

In Stock Maytech Electric Skateboard Splashproof Remote Control MTSKR2005WF IP66 2.4GHZ

Maytech MTSKR2005WF IP66 Splashproof Esk8 Remote Electric Skateboard Elongboard Hand Remote with 3 Speed Modes

If you want to use for water sports, then please order our MTSKR1905WF IP67 waterproof remote Here>

In Stock Maytech MTSKT310DB 310mm New Truck Set with Motor Mount for Dual Belt-driven Skateboard Elongboard Truck Front and Rear Truck

Maytech MTSKT310DB 310mm New Truck Set for Dual Belt-driven Skateboard Elongboard Truck Front and Rear Truck

Related Products: (Click the following pictures to check more products)

Rear Truck for Dual Hub Motor:

Related Products: (Click the following pictures to check more products)

Maytech Brushless Outrunner Sensored Motors

Maytech VESC_TOOL Compitable VESC:

Maytech Fully Waterproof Remote MTSKR1905WF:

Maytech MTSKPS2005 Pulley Belt Comb with 36T 5M Wheel Pulley with Ball Bearing 14T 5M Motor Pulley 51T 5M HTD255 Belt for Electric Skateboard/Elongboard

Maytech MTSKPS2005 Pulley Belt Comb with 36T 5M Wheel Pulley with Ball Bearing 14T 5M Motor Pulley 51T 5M HTD255 Belt for Electric Skateboard/Elongboard

The kit includes: 

1. MTSKP2005C Wheel Pulley: 36T 5M 16mm Width, with 2pcs ball bearing

2. MTSKG2005 Motor Pulley: 14T 5M 16mm Width, with 8mm Hole diameter, compatible with 8mm shaft motor. 

3. MTSKB2005 Belt: 51T 5M HTD 255-5M, 15mm Width.

Compatible Motor: This kit motor pulley is 8mm Hole Diameter, can only work with 8mm shaft motor, below is Maytech motor with 8mm shaft: 

5065-HA/ 5065-HA-C/ 5570-HA-C3/ 6355-HA/ 6355-HA-C/ 6365-HA/ 6365-HA-C/ 6374-HA/ 6374-HA-C

Compatible Truck: MTSKT310DB