Maytech.cn--Maytech official website
In Stock Maytech 65162 Efoil Motor Inrunner Waterproof 9KW Motor for Efoil Electric Hydrofoil
In Stock Maytech 65162 Efoil Motor Inrunner Waterproof 9KW Motor for Efoil Electric Hydrofoil
Couldn't load pickup availability
Maytech Fully Waterproof Efoil Motor MTI65162 100/120/190KV Brushless Inrunner Motor for Electric Surfboard/Efoil/Jetski/Esk8
Specification:
Model No. | MTI65162-120-SF |
KV | 120, if you want other KV, contact agnes@maytech.cn |
Max Current | 300A |
Input Voltage | 6-24S Lipo (25-100V) |
Max Output Voltage | 9KW |
Shaft | Screw Shaft |
Hall Sensor | Without |
Motor Pole Number | 6 |
Waterproof Rank | IP68 Waterproof |
Customize | KV, logo, shaft, cable, connector, etc., contact Email: agnes@maytech.cn |
Customer Test Video on Efoil:
Maytech Self Testing: MTI65162-100-SF+MTSP0504 Prop+300A ESC+1905WF Remote:
Share
















😍 Frequently Bought Together
- In Stock Maytech IP67 Waterproof Remote MTSKR1905WF Controller for Esk8/ Esurf/ Efoil
$99.90 - +
- In Stock 2pcs / 5pcs MTS2009AS Max 300A 85V Anti-spark Switch with Short Cirsuit Protection
$423.70$381.33 - +
- Maytech Waterproof 300A 14S 60V Watercooled ESC for Efoil Electric Surfboard Jetsurf
$762.30$686.07 - +
- In Stock 2pcs/ 5pcs MTSPF7.5HK 300A 75V based on V75/300 SuperESC Watercooled Speed Controller
$519.00$467.10 - +
- Maytech 200A Waterproof Watercooled VESC based on V75/300 for Efoil Electric Hydrofoil
$368.00$331.20

In Stock Maytech IP67 Waterproof Remote MTSKR1905WF Controller for Esk8/ Esurf/ Efoil
Specification:
Model No | MTSKR1905WF (V2), upgraded waterproof and signal strength |
Waterproof Rank | IP67 with 2 layers nanometers coating |
Control Mode | Esk8/ Esurf |
Signal Format | Support Standard PWM (PPM) and UART, output range from 10%-20%, which correspond to ESC/VESCTOOL Compatible controller throttle output range from 0%-100%. |
PWM Signal Output Range | 1ms-2ms for throttle no brake in Esurf mode; 1.5ms-2ms for throttle, 1.5ms-1ms for brake in Esk8 mode. |
Double Source Power Supply | Accept 5V power by ESC built-in BEC or extra 5V power |
Output Signal | Max 3.3V |
Display |
Remote and battery power, signal strength, throttle and brake percentage, RPM; speed, mileage; Current, voltage, temp when work with VESC |
Control Pump | Yes (Relay Switch) |
Control Light | Yes (Transistor Switch) |
Safety Button | Support |
Cruise Control | With in Esurf Mode |
Brake | With in Esk8 Mode |
Wireless Charging | Yes |
Package Includes | Transmitter, receiver, charging Pad, receiver, wristband, 3pcs dupont cable |
Compatible Controllers | VESC/ Focbox/ Other PWM ESCs that has same signal output range with the remote. |
Application | foil assist system, electric propulsion, underwater thruster, electric outboard, Esurf, Efoil, electric hydrofoil, electric surfboard, electric skateboard/ elongboard/ mountainboard, electric paraglider, etc., |
Features:
1. Display speed (km/h or mph) in Esk8 mode (for electric skateboard)2. Display voltage in V, current, temperature when work with VESC based controller
> Get Manual: Remote Manual and Instruction
Click Here: How to Display Volt, Current, RPM with TX and RX?


The remote has 2 Modes, signal output pulse width is different in 2 modes:
- Esurf Mode is 1ms-2ms, no stop no brake, if you use Esurf mode to work with VESCTOOL compatible controller, please use below settings in VESCTOOL and to match with the remote:
PPM Control Type: Current no reverse
PPM Mapping: Pulselength Start: 1.1ms; Pulselength End: 1.9ms; Pulselength Center: 1.5ms
Or you can use wizard mode to detect compatible value.
- Esk8 Mode is 1.5ms-1ms (Brake), 1.5ms-2ms (Speed up), 1.5ms is stop position.
Please noted to match compatible parameters for different modes in VESC_TOOL.


Tips After Using:




In Stock 2pcs / 5pcs MTS2009AS Max 300A 85V Anti-spark Switch with Short Cirsuit Protection
Maytech MTS2009AS Max 300A 85V Electronic Anti-spark Switch Battery Cutoff Switch with Short Circuit Protection for Electric Hydrofoil Efoil Surfboard
Specification:
Model No. |
MTS2009AS |
Max Current |
300A |
Max Voltage |
6-20S Lipo (25-85V), recommend better work under 75V |
Size |
96.5 x 56 x 25 (mm) |
Switch Diameter |
12mm |
Switch Type |
Use NMOS to realize switching on/off Power positive |
Connector | With 4pcs Cold-pressed Terminal Connector |
Function | Protect your controller and power supply system when brake or startup |
Features |
First Switch that can cut off positive pole power in the market; Switch comes with LED light indicator; |
Application | Electric surfboard, efoil, foilboard, jetski, jetboard, jetsurf, motorized hydrofoil, motorcycle, fighting robots, lawnmower robot, Electric mountainboard, ATV, motor bike, etc., |





Maytech Waterproof 300A 14S 60V Watercooled ESC for Efoil Electric Surfboard Jetsurf
Maytech MTSF300A-WP IP68 Waterproof 300A ESC 300A 85V Anti-spark Switch Water Pump Esurf Kit Speed Controller for Efoil/RC Boat
Upgraded Notice Since July 29, 2022.
Upgrade with waterproof junction box for wiring as below picture:
Receiver can be put in the junction box to be waterproof, too:


Please noted for usage:
Max ERPM recommended to use for the ESC is 50000.
ERPM = RPM x Motor pole pairs number




Related Products: (Clicking the following pictures to check specs)
1. IP67 Waterproof Esk8 Remote MTSKR1905WF:
2. Waterproof Watercooled Esurf/Efoil/RC Boat Kit:
3. Maytech Watercooled 300A ESC Not Waterproof:

In Stock 2pcs/ 5pcs MTSPF7.5HK 300A 75V based on V75/300 SuperESC Watercooled Speed Controller
Model No. | MTSPF7.5HK |
Input Voltage | 5-18S Lipo (18V-75V) |
Hardware | based on V75/300 |
Firmware | Updatable |
Current | 300A |
Software | VESCTOOL Compatible |
Heat Sink | With |
Water Cooling | With |
Capacitors | 9pcs 100V 470μf capacitor |
Application | electric skateboard, fighting robot, e-bike, electric motorcycle, efoil, electric surfboard, watercraft, electric boat, underwater ROV, agricultural robots, robotic sprayer, etc |
-Absolute Maximum Current: 350A (According to your motor current)
-Battery Current Max: ≤150A (According to your battery discharge current)


Ports definitions:
- AUX port to supply 12V and 5V to external device;
- PPM port to connect PPM transceivers; Never connect one reclever to two or more VESCs in an array ! Permanent damage may result from Y-PPM wiring
- CAN Port for CAN communication with other devices and controller arrays; Only connect CAN L and CAN H ! GND pins and 5V should never be connected in aVESC array.
- Sensor port for motor Hall sensors (ABI, HALL, magnetic precision encoders);
- SWD port to get direct access to the Chipset. Diagnostics, debugging, and real time data;
- COMM port for various kinds of other communication methods like I2C, ADC, Uart,you can use your Arduino or Raspberry Pi to control the SuperESC!
- USB port for programming.



Features:
Max ERPM(RPM) (separate limits for each direction)
-
With CNC aluminum alloy heat dissipation case, optional water cooling system and forced air cooling system.
-
With larger heat sink case that has better heat dissipation performance.
-
Its heat sink case bottom is coverd by fins that can better heat dissipation.
-
Its PCB board has 4pcs MOS paralleled, could withstand higher current, original version only has 3pcs MOS.
-
Its PCB board with cooper stripe, can reduce resistance in high current, better heat dissipation.
-
With larger capacitor, 9pcs 100V 470μf capacitor, while original version only has 6pcs 80V 470μf.
-
With separate design of strong and weak current circuit board, and between 2 boards added heat sink for better heat dissipation.
-
Exclusive 5V and 12V external power supply interfaces will not cause interference when powering analog circuits such as twist/thumb throttles.
2.Must do a good job of heat dissipation! If place it in a sealed container(recommend touse metal container), it must be forced to be cooled with water. Also make sure your container has enough space for the controller, make sure the cooling tube do not bent, otherwise will influence water flow in cooling tube, also make sure water flow is enough for cooling before office use.
3. Before the new ESC is officially used, please test it with a low-voltage and low-throttle, after success, then slowly increase voltage and throttle. Be sure to pay attention to safety during this period!
4. Recommend to add an electronic switch with short circuit protection function between the ESC and battery, such as MTS2009AS 300A electronic switch or BMS with switch function. It is not recommended to use only contactor without short circuit protection!
5. The battery and motor side terminals must be connected tightly, they can’t be loose. Also please make sure terminals not touch case or other wires, here's the video shows you the way to install cold-pressed terminal connector: https://youtu.be/unFfV9RPPCc
6. In actual use, please use hot melt glue to fix the hall/UART interface cables the corresponding sockets of the ESC, to prevent the cables loose due to the bumps of the vehicle!
7. Please do not disconnect relay switch or electronic switch during usage ! Otherwise it will cause electromagnetic interference, which might damage the controller.
PPM Mapping: Pulselength Start: 1.1ms; Pulselength End: 1.9ms; Pulselength Center: 1.5ms
Recommend Products: Click below pictures to check more information

Pre-order Maytech New Marine 32Bit 300A ESC IP68 Waterproof Smaller Size for Efoil Underwater Thruster Electric Surfboard
Pre-order Maytech New 300A 60V Waterproof ESC Smaller Size for Efoil Underwater Thruster Electric Surfbord
Specification:
Strengths:
Related Products:

Maytech 200A Waterproof Watercooled VESC based on V75/300 for Efoil Electric Hydrofoil
Maytech 200A Waterproof Watercooled VESC based on V75/300 for Efoil Electric Hydrofoil Underwater Scooter Water Sports with waterproof junction box for wiring
Overview:
Specification:
Model No. | MTSPF7.12K-WP | Watercooled | Yes |
Current | 200A | Waterproof | Yes |
Software | VESC_TOOL | BEC | 5V/1.5A |
Input Volt |
18-75V If do not use brake, can use max to 75V, if use brake, please use no exceed 50V. |
PCB Size | 92*52*22mm |
Hardware | Based on V75_300 | Firmware Updatable | Yes |
Case Size | As picture | Net Weight | 130g/pcs |
Feature |
12pcs mosfets; 8-layer PCB; separate high current components and low-curent components to two PCBs; etc |
Application | Efoil, electric hydrofoil, foilboard, SUP board, underwater scooter, foil assist system, outboard, sea scooter, hydrofoil bike, etc., |
Notice:
Never connect one reclever to two or more V6/V75 based SUPERFOC ESCs or VESCs in an array! Permanent damage may result from Y-PPM wiring.
Only connect CAN L and CAN H ! GND pins and 5V should never be connected in a V6/V75 based SUPERFOC ESCs or VESC array.
The waterproof process is our engineer manually make, the process time is about 10-15 working days after order confirmed.
Motor Current Max: ≤200A (According to your motor current)
Absolute Maximum Current: 250A (According to your motor current)
Battery Current Max: ≤100A (According to your battery discharge current)

Features:
- High voltage 18S, High curent 200A, tiny size and compact design, light weight.
- Superior Safety: With over-current protection, over-voltage protection, over-heat protection.
- 2pcs PCBs to separate high and low power components (more stable and reliable).
- 8-layer 3oz PCB Board, 3.4mm thick, supports high current and has efficient heat-dissipation capability. (Other brand PCB is only 1-2mm thick).
- 12pcs high quality Mosfets, greater efficiency, handle higher current.
- ARM 32bit processor, faster data transfer and storage.
- 3pcs Capacitors 63V 820μf, prevent power circuit impact.
- 3pcs Current sampling chips, It can make the current sampling faster and more accurate, and has a good improvement on the FOC and over-current protection functions.
- 6061 Premium Alu-Alloy Case, Quick heat-dissipation, Sleek aluminum finish, comfortable hand-feeling.
- Removable cooling fan, 20W high power for quick cooling. Ensure reliable performance with excellent temperature control technology
- USB Type C port- easy to connect and program settings.
- Firmware standard: VESCTOOL automatically recognizes this ESC as 7.5_300. This firmware can be used.
Features:
- High voltage: If use current mode, without brake, max voltage is 75V; If use current mode with brake or duty cycle mode, max voltage is 12S lipo (Max 50.4V).
- High current: 200A
- Compatible with brushed and brushless motors, intrunner and outrunner motors Sensored or Sensorless operation + Hybrid mode
- Adjustable Forward/Backward/Brake
- Regenerative Braking Function
- Configurable RPM, Current, Voltage and Power limits
- Support PPM, Analog (ADC), UART, Canbus input
- Communication ports: USB, CAN, UART
-
Support FOC sine wave mode
-
Throttle curve and ramping for all input sources
- Seamless 4-quadrant operation
- Motor Revolution, Amp Hour, Watt Hour counting
- Real time data analysis and read out via communication ports
- Adjustable protection against:
Max Motor Current and Input(Battery) Current limits
Max ERPM(RPM) (separate limits for each direction)
Max Power (Wattage)
Max Motor and ESC Temperature
Max Regenerative Braking Current (separate limits for the motor and the input)
Attention Points when you receive the controller Please:
- When you receive the controller, please test without load and do not connect motor, first check if the controller can successfully connect to your computer, if ok, then connect to motor and you can start to adjust parameters.
- Do not use switching power supply, the instant voltage when switching power supply connect to controlleris very high, which would easy damage the controller.
- Do not push the throttle too hard when test without load, gently and slowly speed up.
- Be cautious when adjust parameters, if parameters set mistake, would also easy damage the controller.
- Do not recommend to work with BLDC mode, please use FOC mode.
- If you use UART port, the wire better do not over 0.5m or even shorter, and better use Stranded wire.
Above notices are only suggestions based on the experience of our engineers. how to actually operate is up to you. Parameters for different setup is also different, please noted.
Related Products: Click the following pictures to check specs
Maytech MTSKR1905WF waterproof remote for water sports: In stock
Maytech VESCTOOL Compitable SuperESC:
Application:
Electric skateboard, Esk8, Eskate, Elongboard, Mountainboard, Offroad skateboad, All terrain skateboard, Eskate, E-bike, Electric bike, Electirc motorcycle, E-scooter, Electric scooter, motorized skateboard, ROV/RPVEE, Remote operated vehicles, underwater robots, Underwater robotics, Underwater remotely operated vehicles, Subsea robots, Cablecam, Cable camera, Broadcast, IBC2019, Ultra drones, Security monitoring robots, Robots for security and safety monitoring in harsh terrain, Agile robots, SAutonomous agile robots, Security robots, Autonomously monitor security, Combat robots, Fighting robots, Electric surfboard, Efoil, etc.,